
BMW 7 Series E65/E66.
The coilover guide.
Shop the coiloversMany E65 and E66 7 Series cars have rear air suspension or electronic dampers. Find out what yours has before anything else, then set the height around clearance and travel.
7 Series E65 and E66 history
The E65 saloon and long-wheelbase E66 were BMW's 7 Series from 2001 to 2008. BC lists I-38 for the saloon in BR RN form, with no front top mount and a rubber rear mount.
These cars were built with a lot of suspension technology, including rear air springs on many and Electronic Damper Control on others. A coilover kit replaces those parts, so the factory specification decides the work involved.
BMW launched the E65 in 2001, the first car with iDrive, and followed it with the long-wheelbase E66. The range covered six-, eight- and twelve-cylinder petrol engines and diesels, with a facelift in 2005.
Rear self-levelling air suspension was standard on some models and optional on others, and Electronic Damper Control and Dynamic Drive active anti-roll bars were available. Check the car's options list rather than its badge.
The E65 was replaced by the F01 in 2008. Kits for the earlier E38 and later F01 use different references.
Start with your 7 Series E65/E66.
Confirm the chassis, year and existing suspension before choosing your setup.

E65 saloon with steel springs
BC lists I-38 for the 2001-2008 7 Series saloon, with default rates of 6 kg/mm front and 4.5 kg/mm rear. Give the supplier the engine, build date and options list, and ask it to confirm the kit for your car.
Check my E65
Rear air suspension and E66
BC's listing does not say how the kit handles rear air springs or the long-wheelbase E66. Tell the supplier if the car has either, and ask what is needed for the air system and warning lights.
Check my air-suspension 7 Series
EDC and Dynamic Drive
Electronic Damper Control and Dynamic Drive both connect to the suspension. Ask the supplier how the kit treats them, and what the car will show afterwards, before ordering.
Check my EDC 7 SeriesChoose a kit for your car and driving
Tell the supplier about your tyres, usual roads and any circuit plans. Budget for fitting, alignment and setup as well as the kit. Each example below still needs an application check for your exact car.
BC lists I-38 BR RN for the E65 saloon. Confirm the car has steel springs and no EDC before ordering.
Read the buying advice
I-38 is a possible starting point for a steel-spring E65 once the supplier has confirmed fitment. It has 30-way rebound adjustment and height set separately from spring preload. Agree a modest height that keeps the ride a large saloon needs.
- Confirm steel springs
- Leave room for suspension movement
- Include alignment
Replacing rear air springs with coilovers involves more than the kit. Ask the supplier before ordering.
Read the buying advice
Ask the supplier what is needed to replace the rear air springs and how the car's systems will respond. Get the extra parts and wiring work quoted alongside the kit, and confirm whether the E66 needs anything different.
- Confirm the factory air system
- Ask about the E66
- Get the work quoted together
Coilovers with manual damping replace EDC. Agree what happens to the warning lights before booking fitting.
Read the buying advice
Ask BC and the fitter how the kit handles Electronic Damper Control and whether Dynamic Drive is affected. Settle that before ordering so the car is fitted in one visit.
- Ask about EDC wiring
- Check Dynamic Drive
- Book fitting once
Check where the rear spring carries the load
On a standard BMW E65, the rear spring and shock absorber are mounted separately.
Layout only. Mounts and spring seats vary by kit.On a steel-spring E65, the rear spring sits separately from the damper. BC lists 6 kg/mm front and 4.5 kg/mm rear; the springs sit in different positions, so the figures are not a direct comparison of stiffness at the wheel.
On a car with rear air suspension, the air springs, compressor and height sensors are part of one system. Replacing them changes more than the dampers, so get the full scope of work from the supplier.
Read about ride height and spring preload
Plan the fitting before the car arrives
Give the workshop the kit reference and the car's options list before it orders fitting parts. On a car with air suspension, EDC or Dynamic Drive, agree in advance how those systems will be handled. Have it check the top mounts, bearings, bushes and drop links, and ask for a written list of the parts it will reuse or replace.
Once fitted, check clearance with the actual wheels and tyres through steering lock and suspension travel. Let the car settle at the agreed height before alignment, and record the starting damper settings.
Check the factory suspension
Confirm from the VIN data whether the car has rear air springs, EDC or Dynamic Drive, and whether it is an E65 or long-wheelbase E66. That decides the parts and work involved.
Measure the wheel and tyre clearance
Give the fitter the wheel width, offset and tyre size, including any spacers. At the intended height, check tyre clearance to the arches and wheel clearance to the springs, dampers and adjusters.
Leave travel for normal use
Tell the workshop about your usual roads and what the car usually carries. At the proposed height, check how much room remains for the suspension to compress with the kit's bump stops fitted.
Set the geometry after the height
Have the car aligned once the ride height is final and the suspension has settled. Get the readings and starting damper settings recorded.
The current 7 Series E65/E66 range.
See the controls and hardware in the listed kit.
I-38 is listed for the 2001-2008 7 Series saloon under E65, in BR RN form with no front top mount and a rubber rear. BC gives default rates of 6 kg/mm front and 4.5 kg/mm rear and 30-way rebound adjustment. Ask BC about the E66, rear air suspension and EDC.
View BC Racing 7 Series E65/E66 kitsFind your 7 Series E65/E66 coilovers.
Prices include UK VAT. Choose an application and brand, then open a kit for its current options and availability.
1 listing
Selected application: All 7 Series E65/E66 applications
Match the drivetrain, body style and axle-load limits on the product page before ordering.
![BC Racing Coilovers - BMW 7 Series Sedan (01-08) [E65]](/images/09cf8cd191b679-480.webp)
BC Racing · BCR-I-38
BC Racing Coilovers - BMW 7 Series Sedan (01-08) [E65]
Check the exact application
All 7 Series E65/E66 kit links and part numbers
Before you order.
Identify your car
Send the engine, body length, build date, VIN and options list, including rear air suspension, EDC and Dynamic Drive.
Match the kit
Confirm the full kit reference for your car and check that it covers your engine, drivetrain and build date.
Check what’s included
Ask for a written list of the mounts, springs and fitting parts supplied with the kit. Confirm which existing parts will be reused and which need replacing.
Check your modifications
Supply wheel width, offset and tyre size, together with the intended use. Agree a height with adequate clearance and suspension travel.
Plan fitting
Get fitting, alignment and setup quoted together, including any air-suspension or electronic work. Confirm delivery timing before reserving workshop time.
Questions about BMW 7 Series E65/E66 coilovers.
Check the details before choosing your kit.
Can I fit coilovers to an E65 with rear air suspension?
Ask the supplier first. BC's listing does not say how the kit handles rear air springs, which involve the compressor, sensors and warning lights.
Does I-38 fit the long-wheelbase E66?
BC's listing names the 7 Series saloon under E65. Ask BC to confirm an E66 before ordering.
Do E38 kits fit the E65?
No. The E38 has its own BC reference, I-23.
What happens to EDC?
A kit with manually adjusted dampers replaces it. Ask BC how its kit handles the wiring and warning lights.
How low should I set the car?
Choose the height with the fitter using the kit instructions, wheel clearance and room for suspension movement. A lowering range shows what is available, not a target for every E65. Check the alignment at the final height.
When should I book fitting?
Agree the specification and delivery timing with the supplier first, then book fitting and alignment once the parts are confirmed.
Let’s talk suspension.
Send the E65's engine, build date, options list and current suspension details. Include the kit reference you are considering so the application and fitting parts can be checked together.



