
BMW Z4 E89.
The coilover guide.
Shop the coiloversFind out whether the car has Adaptive M Suspension first. Then choose a kit by how you drive, and set the height around tyre clearance and usable suspension travel.
Z4 E89 history and suspension
Every E89 is a two-seat roadster with a folding aluminium hardtop, from the sDrive18i to the sDrive35is. There was no Z4 M in this generation. The listed kits cover the E89 by chassis, but some exclude particular factory equipment. Give the supplier the engine, build date and options list before comparing prices.
Adaptive M Suspension uses electronically controlled dampers. Eibach's listing excludes cars with electronic suspension systems, so a car with that option needs the manufacturer to confirm what is required before any kit is ordered.
BMW launched the second Z4 in 2009 and built it at Regensburg in Germany until 2016. A two-piece aluminium hardtop folds electrically into the boot, so one body replaced the earlier separate roadster and coupe. The E85/E86 that came before and the G29 that followed use different parts and have their own guides.
Adaptive M Suspension was an option. BMW describes it as sitting 10 mm lower than the standard car, with electronically controlled dampers whose settings change with the driving mode. A coilover kit with manually adjusted dampers replaces that system. Have the supplier explain what happens to the car's electronics, warning lights and driving modes before choosing.
Before choosing the finished height, have the workshop check the bushes, top mounts and surrounding bodywork. Include any repairs in the fitting plan. Wheel clearance and the suspension travel left at that height should decide how far the car comes down.
Start with your Z4 E89.
Match the model year, drivetrain and body style before comparing brands.

Standard or M Sport suspension
BC lists I-111 for 2009-2016 Z4s under E89, SPAX lists RSX108 and RSX3-216 from April 2009, and Eibach lists PSS65-20-019-01-22 for the sDrive18i to sDrive35is. Give the supplier the engine, build date and options list. Ask it to confirm the part reference and supplied mounts for that car.
Check my Z4 E89
Adaptive M Suspension
Eibach's fitting notes exclude electronic suspension systems. The BC and SPAX listings do not say how they treat the factory electronic dampers. Tell the supplier the car has Adaptive M Suspension and ask what it recommends for the electrical connections, warning lights and driving modes before ordering.
Check my Adaptive M car
Track days and events
The SPAX RSX3-216 has separate bump and rebound adjustment, and BC's I-111 offers 30-way damping adjustment. Tell the supplier about the tyres, circuits and how often the car runs. Ask it to confirm spring rates and starting settings for that use.
Check my track Z4Choose a kit for your car and driving
Tell the supplier about your tyres, usual roads and any circuit plans. Budget for fitting, mounts, alignment and setup as well as the kit. Each example below still needs an application check for your exact car.
BC lists I-111 with a pillowball front and rubber rear mount. Have the application and factory suspension checked before ordering.
Read the buying advice
The I-111 is a possible starting point for a road E89 once the supplier has confirmed fitment. BC gives default rates of 5.5 kg/mm front and 9 kg/mm rear, and the height adjusts separately from spring preload. Agree a height that clears your wheels and leaves room for the suspension to compress over bumps.
- Confirm the engine and options
- Leave room for suspension movement
- Include mounts and alignment
Eibach lists PSS65-20-019-01-22 with front and rear axle-load limits and excludes electronic suspension. Check both before ordering.
Read the buying advice
Eibach gives maximum axle loads of 870 kg front and 1,000 kg rear for this kit, with 15-40 mm front and 10-35 mm rear adjustment in its catalogue. The front height is set on the threaded strut and the rear on a separate adjustable unit. Eibach notes that some cars on original wheel sizes may need spacers for clearance, and that extra original parts may be required.
- Check the axle-load limits
- Confirm no electronic dampers
- Ask which original parts are needed
SPAX lists RSX3-216 with separate bump and rebound adjustment for the Z4 E89. Confirm the application and settings for your use.
Read the buying advice
RSX3-216 lets you set bump and rebound separately, which helps when the same car runs on the road and on circuit tyres. SPAX lists 35-65 mm of lowering front and rear, measured from the original suspension. Agree spring rates and starting settings with the supplier, and confirm delivery timing before booking fitting.
- Confirm the exact application
- Provide road and circuit tyre details
- Agree settings and delivery timing
Check where the rear spring carries the load
On a standard BMW Z4 E89, the rear spring and shock absorber are mounted separately.
Layout only. Mounts and spring seats vary by kit.The E89's rear coil spring sits separately from the damper. The spring supports the car through its own seats, and the damper controls movement. Eibach's note that the rear height is set on a separate adjustable unit reflects that layout.
A kit that keeps the separate spring adjusts the rear height at the spring seat. A true rear coilover would put the spring around the damper, so the damper mounts would also carry the spring load. Ask which layout the kit uses before comparing spring rates.
Spring rates only compare like with like. A rear spring mounted away from the damper acts at a different point on the suspension, so its rate does not translate directly into stiffness at the wheel. Agree rates with the supplier for the layout you are buying, and check the alignment at the final ride height.
Read about ride height and spring preload
Inspect the car before setting the height
Give the workshop the kit reference and the car's options list before it orders fitting parts. On a car with Adaptive M Suspension, agree in advance how the factory damper wiring will be handled. Have the workshop inspect the bushes, top mounts and drop links, and ask for a written list of the parts it will reuse or replace.
Once fitted, check clearance with the actual wheels and tyres through steering lock and suspension travel. Let the car settle at the agreed height before alignment, and record the starting damper settings. Follow the kit manufacturer's instructions for later checks.
Check the factory suspension option
Confirm from the options list whether the car has standard, M Sport or Adaptive M Suspension. Adaptive M changes what the kit has to replace and may affect warning lights and driving modes. Settle that with the supplier before ordering.
Measure the wheel and tyre clearance
Give the fitter the wheel width, offset and tyre size, including any spacers. At the intended height, check tyre clearance to the arches and wheel clearance to the springs, dampers and adjusters. Eibach notes that some cars on original wheel sizes may need spacers.
Leave travel for normal use
Tell the workshop about your usual roads and the luggage the Z4 carries, remembering that the folded hardtop takes boot space. At the proposed height, check how much room remains for the suspension to compress with the kit's bump stops fitted.
Set the geometry after the height
Have the car aligned once the ride height is final and the suspension has settled. Get the readings and starting damper settings recorded. If the alignment cannot reach the agreed figures, ask the specialist what hardware is needed; damper adjustment will not correct it.
The current Z4 E89 range.
Compare the controls and hardware included in each range.
I-111 is listed for 2009-2016 Z4s under E89, in BR form with a pillowball front and rubber rear mount. BC gives default rates of 5.5 kg/mm front and 9 kg/mm rear and 30-way rebound adjustment. Ask BC how the kit treats a car with Adaptive M Suspension, and check the supplied mounts for your car.
View BC Racing Z4 E89 kitsPSS65-20-019-01-22 is listed for the E89 from May 2009 to August 2016, sDrive18i to sDrive35is. It has maximum axle loads of 870 kg front and 1,000 kg rear and excludes electronic suspension systems. Eibach's fitting notes mention possible wheel spacers and extra original parts, so read them with the supplier before ordering.
View Eibach Z4 E89 kitsRSX108 has adjustable damping and RSX3-216 has separate bump and rebound adjustment. Both are listed for the Z4 from April 2009, with 35-65 mm of lowering front and rear. Those figures depend on the car's original suspension. Have SPAX confirm the engine, build date and factory suspension option.
View SPAX Z4 E89 kitsFind your Z4 E89 coilovers.
Prices include UK VAT. Choose an application and brand, then open a kit for its current options and availability.
4 listings
Selected application: All Z4 E89 applications
Match the drivetrain, body style and axle-load limits on the product page before ordering.

Eibach · PSS65-20-019-01-22
Eibach Pro-Street S Coilover Kit for BMW Z4 ROADSTER (E89) - PSS65-20-019-01-22
Check the exact application

SPAX · RSX108
SPAX RSX Coilover Kit for BMW Z4 Z89 - RSX108
Check the exact application
![BC Racing Coilovers - BMW Z4 (RWD) (09-16) [E89]](/images/09cf8cd191b679-480.webp)
BC Racing · BCR-I-111
BC Racing Coilovers - BMW Z4 (RWD) (09-16) [E89]
Check the exact application

SPAX · RSX3-216
SPAX RSX Double Adjustable Coilover Kit for BMW Z4 Z89 - RSX3-216
Check the exact application
All Z4 E89 kit links and part numbers
- BC Racing · BCR-I-111: BC Racing Coilovers - BMW Z4 (RWD) (09-16) [E89]
- SPAX · RSX108: SPAX RSX Coilover Kit for BMW Z4 Z89 - RSX108
- SPAX · RSX3-216: SPAX RSX Double Adjustable Coilover Kit for BMW Z4 Z89 - RSX3-216
- Eibach · PSS65-20-019-01-22: Eibach Pro-Street S Coilover Kit for BMW Z4 ROADSTER (E89) - PSS65-20-019-01-22
Before you order.
Identify your car
Send the engine, build date, VIN and options list, including whether the car has Adaptive M Suspension and any previous suspension changes.
Match the kit
Confirm the full kit reference for your car. Check that it covers your engine and build date, and ask how it handles the factory suspension option.
Check what’s included
Ask for a written list of the mounts, springs and fitting parts supplied with the kit. Confirm which existing parts will be reused and which need replacing.
Check your modifications
Supply wheel width, offset and tyre size, together with the intended use. Agree a height with adequate clearance and suspension travel.
Plan fitting
Get fitting, alignment and setup quoted together, including any wiring work, inspection and repairs. Confirm delivery timing before reserving workshop time.
Questions about BMW Z4 E89 coilovers.
Check the details before choosing your kit.
Can I fit coilovers to a Z4 E89 with Adaptive M Suspension?
Ask the manufacturer before ordering. Eibach's listing excludes electronic suspension systems, and the BC and SPAX listings do not say how they treat the factory electronic dampers. Have the supplier explain the wiring, warning lights and driving modes for your car.
Is there a Z4 M version of the E89?
No. BMW did not build a Z4 M in this generation. The fastest version is the sDrive35is, which Eibach includes in its listed engines.
Do E85 or G29 Z4 kits fit the E89?
No listing here suggests that. Each generation has its own kit references. Use the E89 application for a 2009-2016 car.
Does the folding hardtop change the kit choice?
Every E89 has the hardtop, so the listed kits are written for that body. Give the supplier the engine, options and how you use the car so it can confirm the spring rates.
What do Eibach's axle-load limits mean?
They give the heaviest front and rear axle load the kit is listed for: 870 kg and 1,000 kg for this reference. Check them against your car's documents along with the application table.
Will I need wheel spacers?
Possibly. Eibach notes that some cars on original wheel sizes may need spacers for clearance. Give the fitter the wheel and tyre details and check clearance with the actual parts.
How low should I set the car?
Choose the height with the fitter using the kit instructions, wheel clearance and room for suspension movement. A lowering range shows the adjustment available, not a target for every Z4. Check the alignment at the final height.
When should I book fitting for a kit on backorder?
Agree the specification and delivery timing with the supplier first. The Eibach and SPAX options are listed on backorder without a dated arrival. Book fitting and alignment once the parts and their timing are agreed.
Let’s talk suspension.
Send the Z4's engine, build date, options list and current suspension details. Include the kit reference you are considering so the application, fitting parts and any Adaptive M work can be checked together.




