Blue petrol BYD F0 five-door hatchback with graphite multi-spoke wheels at a stone-walled country turnout

BYD F0 FWD (2009–2015).
The coilover guide.

Shop the coilovers

BC lists ZP-01 for the petrol F0 FWD, 2009–2015. Identify the car, check the mounting package and plan the rear spring and damper work before ordering.

Which F0 FWD (2009–2015) do you have?1 listed kit · 1 brandReviewed 15 November 2026

A small petrol hatch with its own application.

Send the F0's build details, existing suspension and wheel sizes when checking the V1 VN package. Include any earlier lowering springs or adjustable rear seats, so the fitter knows what is already on the car.

Choose a height for the roads you drive and loads you carry. If you plan to use the car on circuit, discuss that with the fitter too. All three uses refer to the same kit, so agree the springs, mounts and fitting work before ordering.

BYD launched the F0 economy model in September 2008. The original small five-door hatchback paired a three-cylinder petrol engine with a short, upright body. BC's listed application starts in 2009; the car's launch date does not extend that kit's stated coverage.

BYD's historical F0 specification gives MacPherson front suspension and a torsion-beam rear. Its repair manual shows the rear coil springs on their own seats beside separate dampers. Those positions matter when discussing the height adjustment and rear parts supplied with the kit.

BC assigns ZP-02 to Qin FWD. The shop currently calls that listing Fo, 2013–2018, so it is excluded from this F0 guide. Give the kit code with the car's build details when asking for help.

Start with your F0 FWD (2009–2015).

Confirm the chassis, year and existing suspension before choosing your setup.

Pearl-white petrol BYD F0 on graphite multi-spoke wheels outside a brick workshop

Petrol F0 FWD, 2009–2015: check ZP-01

Provide the build year and market specification, photographs of the fitted suspension and the wheel and tyre sizes. BC lists ZP-01 as V1 VN for F0 FWD. Check its supplied assembly against the original mounts and any previous changes.

Check my F0 application

What do you want
from the car?

Choose advice for everyday driving, occasional circuit days or a dedicated track project.

Choose a usable height for the roads and loads you carry.

Read the buying advice

Tell the fitter about passengers, luggage, speed humps and parking entrances on your normal routes. Have spring retention, available travel and tyre clearance checked at the proposed height. Inspect the parts that will be reused and include final alignment in the fitting budget.

  • Describe usual passengers and loads
  • Keep useful travel and clearance
  • Inspect retained parts before fitting
Plan my F0 road setup

Discuss both uses and tyre sets before agreeing the package.

Read the buying advice

Give the fitter both wheel and tyre specifications if you change them for circuit days. Discuss spring rates and damper settings with the car's available travel and loads. Check the brakes and tyres for the intended use, and record the alignment and starting settings before making later changes.

  • List road and circuit wheel sets
  • Agree springs and working travel
  • Record alignment and settings
Discuss my F0 road and circuit use

Have the builder assess the complete car and event requirements.

Read the buying advice

Describe changed hardware, tyres and the events you intend to enter. The builder needs to assess the spring and damper package alongside the mounts, working travel and clearance. A road-model listing does not establish competition eligibility, and different rates or mounting arrangements require a separate enquiry.

  • Describe changed hardware and tyres
  • Check the complete mounting package
  • Review the intended event requirements
Discuss my F0 circuit project

The rear spring sits beside the damper.

Separate rear spring and damperThe coil spring rests between its own seats, beside a separate shock absorber. This fixed component diagram does not show vehicle dimensions, mounting hardware or suspension movement.SpringDamper

The F0 repair manual shows separate rear coil springs and dampers.

Component layout only. Mounts, dimensions and adjusters vary by kit.

BYD's F0 repair manual shows coil springs on the rear twist beam with upper and lower cushion rubbers. The dampers mount separately. The drawing identifies those component positions.

Confirm the rear springs, seats, dampers and retained parts in the exact ZP-01 package. Where the supplied kit provides separate spring-seat and damper adjustments, follow its own instructions and have the fitter check spring retention, working travel and clearance at the intended height.

Read about running height and spring preload
Mechanic kneeling with a hand torch beside the front wheel of a blue petrol BYD F0 standing on a workshop floor

Include the retained parts in the fitting plan.

Give the fitter photographs of the existing front mounts, rear spring seats and damper fixings. The shop lists V1 VN with no front top mount and a rubber rear arrangement. Confirm exactly which parts the supplied kit includes or reuses, then inspect their condition before booking the work.

BYD's F0 owner manual warns that changes to suspension, tyres and chassis can affect airbag operation, and advises consulting an authorised service station before modifying suspension. Include the relevant vehicle checks, tyre clearance and final alignment in the plan for the changed car.

Front mounts and bearings

Agree which front mounts and bearings the supplied VN assembly retains. Have worn rubber, bearings and damaged fixings assessed before fitting.

Rear seats and beam bushes

The rear spring has its own seats and cushion rubbers. Ask the fitter to inspect them, the damper mountings and the beam bushes. Identify any existing lowering springs or adjustable seats when agreeing what will be replaced.

Wheels, tyres and clearance

Provide wheel widths, offsets, tyre sizes and spacer thickness. Have clearance checked through the intended steering and suspension movement with normal loads included. Set the height around the roads and entrances the car uses.

Alignment and vehicle condition

Include final alignment after the height is settled, plus the vehicle checks required for the changes. For circuit plans, have the brakes and tyres assessed for that use. Keep the measurements and damper settings with the service record.

The current F0 FWD (2009–2015) range.

See the controls and hardware in the listed kit.

BC Racing

The shop lists one F0 V1 VN application, BCR-ZP-01, with default rates of 4 kg/mm front and 3 kg/mm rear. BC's V1 application list identifies F0 FWD, 2009–2015, in the VN column. BC describes V1 as one-way adjustment; use the instructions for the supplied kit. Confirm the mounting package and any retained original parts before ordering.

View BC Racing F0 FWD (2009–2015) kits

Find your F0 FWD (2009–2015) coilovers.

Prices include UK VAT. Choose an application and brand, then open a kit for its current options and availability.

1 listing

Selected application: All F0 FWD (2009–2015) applications

Match the drivetrain, body style and axle-load limits on the product page before ordering.

All F0 FWD (2009–2015) kit links and part numbers

Before you order.

  1. Identify your car

    Give the petrol F0's build year and market specification; this listed application is 2009–2015 FWD.

  2. Match the kit

    Match ZP-01 to the car. The ZP-02 listing has a Qin application in BC's list and is excluded here.

  3. Check what’s included

    Agree the springs, rear seats, dampers and supplied or retained mounting parts.

  4. Check your modifications

    Provide wheel, tyre and spacer measurements, then plan travel and clearance checks with the usual loads.

  5. Plan fitting

    Plan fitting, final alignment and required vehicle checks; confirm availability before booking.

Questions about BYD F0 FWD (2009–2015) coilovers.

Check the details before choosing your kit.

Which F0 application is listed here?

BC lists ZP-01 for the petrol F0 FWD, 2009–2015. The shop reference is BCR-ZP-01 with V1 VN specification. Confirm the build, existing hardware and supplied package before ordering.

Why is the other Fo listing excluded?

The shop labels BCR-ZP-02 as Fo, 2013–2018, but BC's manufacturer application list assigns ZP-02 to Qin FWD. It is excluded from this F0 guide. Give the car's identity and the kit code when asking for an application check.

Are the rear springs separate from the dampers?

Yes. BYD's F0 repair manual shows rear coil springs on their own seats on the twist beam, with separate dampers. Confirm the rear parts in the supplied ZP-01 assembly and follow its fitting instructions.

Does V1 VN include new top mounts?

The shop describes this VN application as having no front top mount and a rubber rear arrangement. Confirm the exact supplied and retained parts, including the front bearings and rear mounting hardware. The existing parts need their condition checked before reuse.

Which spring rates are listed?

The listed default rates are 4 kg/mm front and 3 kg/mm rear. Confirm the supplied springs for the intended car and use. A different rate is a separate enquiry, not an extra selectable kit shown here.

What adjustment does V1 provide?

BC describes V1 as one-way adjustment. Follow the instructions for the supplied assembly and record its starting settings. Ask the fitter to explain the front and rear height adjustments.

How should I choose the running height?

Discuss the roads, entrances and normal loads with the fitter. Have spring retention, working travel, tyre clearance and underbody clearance checked at the proposed height, then include final alignment. A low-looking stance alone does not establish usable travel.

Does BYD give advice about suspension changes?

The F0 owner manual warns that suspension, tyre and chassis changes can affect airbag operation, and advises consulting an authorised service station before modifying suspension. Ask the fitter which vehicle checks the proposed changes require.

Does this cover other BYD models or similar-looking hatchbacks?

This is the petrol F0 application identified by BC's ZP-01 listing. Qin and other models need their own application evidence. A similar body shape does not establish interchangeable suspension parts.

Why do the driving-use cards lead to an enquiry?

They help you describe the loads, tyres and planned use to the fitter or builder. There is one listed F0 kit here, and the three uses are not separate priced suspension levels.

Let’s talk suspension.

Tell us your F0's build details, fitted suspension and wheel sizes. Include previous changes, normal loads and how you intend to use the car.

Call Coilovers Direct0115 647 9207
or

Your registration isn’t saved to your garage.

Ask about my carFind the listed kits above, or ask us about your setup.