Green BMW E28 four-door saloon outside a stone coach house

BMW E28.
The coilover guide.

Shop the coilovers

Check the front struts before ordering coilovers for your E28. BC Racing lists the I-34 for 52mm struts and specifies welding, so ask your fitter to confirm the conversion and its cost.

Which E28 do you have?1 listed kit · 1 brandReviewed 18 November 2026

Identify the E28 and the parts fitted now

Include the wheels and tyres you intend to use in the setup discussion. Clearance needs checking through steering and suspension movement at the proposed height, with allowance for your usual load. Tell the fitter about earlier suspension conversions before agreeing which parts to use.

The current shop kit is BC Racing I-34 in BR RA specification. Budget for the strut conversion and supporting repairs as well as the kit. At the rear, have the geometry measured and agree any correction separately: the standard E28 arrangement has no routine camber and toe adjustment.

BMW introduced the second-generation 5 Series in 1981. The range later gained diesel and economy-focused eta models, and the E28 became the basis for the first M5. BC lists I-34 for E28 saloons from 1981 to 1988.

Tell GSM if your car is an M535i or M5. BC's E28 row does not establish I-34 fitment for every engine or suspension version. Include the original market and any changes made since the car was built.

For a restored or modified car, ask the fitter to identify the front struts actually present. Previous replacement parts and conversions can change what needs measuring or retaining. Have corrosion, damaged mounting areas and worn joints assessed before agreeing the conversion.

Start with your E28.

Confirm the chassis, year and existing suspension before choosing your setup.

Green E28 saloon parked outside a stone coach house

Standard E28 saloons

Send the full model, engine and build details with the front strut measurement. BC names the E28 saloon, rear-wheel drive and 52mm struts for I-34. Ask for the exact kit, supplied mounts and welding work to be confirmed for your car before ordering.

Check my E28 saloon
Burgundy E28 M5 saloon beside closed pit garages

M535i and M5

State the exact model and factory suspension specification, including any self-levelling equipment actually fitted. Have the front struts, rear assemblies and required replacement parts checked individually. The general E28 application is not confirmation that one kit suits both cars.

Check my M535i or M5
Silver E28 four-door saloon outside a brick workshop

Imports and uncertain build dates

Provide the original market and build date as well as the registration year. The UK kit must be confirmed for the car; a regional BC listing's dates or default specification are not a substitute. Include photographs and measurements of unfamiliar or replacement suspension parts.

Check my imported E28
Mechanic with a clipboard beside a green E28 on a workshop floor

Restored cars and previous conversions

Describe any changed front struts, rear mounts, self-levelling work or alignment hardware. Include engine, brake and wheel changes in the enquiry. Agree which existing parts can be used and what the installer needs to repair or replace before quoting for I-34.

Check my existing conversion

What do you want
from the car?

Choose advice for everyday driving, occasional circuit days or a dedicated track project.

Kit starts from£1,049.00inc. VAT · I-34 BR RA · confirm your car and fitting work

Once fitment and the welding work are confirmed, discuss the current I-34 BR RA kit with your fitter.

Read the buying advice

Explain what you want to change about the present ride and how much lower you want the car to sit. BR has one damping control that changes compression and rebound together. Agree the springs and mounts for the ordered kit, then leave room for suspension travel, speed humps and your usual passengers or luggage. Include worn supporting parts in the budget.

  • Confirm the 52mm strut application
  • Allow for specialist fitting
  • Keep usable travel and clearance
View our recommended kit
Kit starts from£1,049.00inc. VAT · I-34 BR RA · confirm fitment and setup

If I-34 is confirmed for your car, discuss how to set it up for road use and occasional circuit days.

Read the buying advice

Give the fitter details of both wheel and tyre sets if you change them for circuit days. Discuss the car's weight and any brake or chassis changes before settling on springs, ride height and damping. Check how the adjusters can be reached, and plan inspections and servicing. The listed spring rates alone do not establish that a setup suits your tyres or circuit use.

  • Provide both wheel and tyre specifications
  • Agree the setup for your actual use
  • Plan inspections and servicing
View our recommended kit

Start with the finished car's weight, tyres and suspension hardware.

Read the buying advice

Tell the builder about altered struts, mounts and rear alignment hardware, alongside any engine, brake or aero changes. Agree what the intended event permits and how the car will be inspected. An M5 badge or a shared chassis code does not settle the kit choice. Ask for a complete specification for the project before ordering parts.

  • Measure the completed car
  • Identify existing suspension alterations
  • Check the intended event's rules
Discuss my E28 circuit project

The rear spring sits around the damper

A spring surrounding a damperA fixed component diagram. The coil spring surrounds the shock absorber and rests on its spring seats. It does not show vehicle dimensions, mounting hardware or suspension movement.Coil springDamperSpring seat

The rear spring surrounds the damper on a standard E28.

Component layout only. Mounts, dimensions and adjusters vary by kit.

BMW's technical training places the E28, including M5, in its semi-trailing-arm rear suspension group. The drawing shows the coil spring around the damper. This illustration explains that factory arrangement; it does not show the dimensions, mounts or parts supplied with I-34.

Have the complete rear assemblies and any retained hardware confirmed for the car. Identify self-levelling equipment if present and agree what replacing it involves. Existing conversions need their own inspection before the new kit is specified.

BMW describes the standard rear arrangement as having no routine alignment adjustment. Ask the workshop to measure it and explain any correction that is actually possible with the parts fitted. New coilovers or front camber hardware do not create rear camber and toe adjustment. Deal with worn parts or damaged mounting areas before judging the final readings.

Understand height and spring preload
Mechanic holding a clipboard beside a green E28 saloon on a level workshop floor

Budget for the conversion and supporting repairs

Ask the fitter to inspect the front struts, suspension mounting areas, bushes and joints before finalising the quote. I-34 requires welding. Obtain the current kit-specific fitting requirements and agree the specialist work, supplied parts and retained hardware before the car is dismantled. Include any corrosion or damage repairs that the inspection identifies.

Provide wheel widths, offsets, tyre sizes and spacer details. Have clearance to the suspension, arches and liners checked through steering and suspension movement at the intended height. Include height setting, alignment measurement, any agreed correction and follow-up checks in the job. Check the kit's current availability before booking workshop time.

Front struts and previous welding

Have the actual struts identified and assessed, including any earlier conversion work. Confirm the 52mm application against I-34's current instructions and agree whether the parts are suitable for the required work. Keep measurements and photographs with the fitting enquiry.

Wheels, tyres and spacers

Give the fitter the complete wheel and tyre specification, including both sets if used. Check arch and suspension clearance through full steering lock and suspension travel at the proposed height. A similar-looking wheel on another E28 does not establish clearance on yours.

Mounts, structure and worn parts

Include top mounts, bushes, joints and suspension mounting areas in the inspection. Price the repairs that are needed alongside the conversion. Ask for the complete supplied-parts list and identify any original hardware that must be retained or replaced.

Rear alignment and self-levelling

Identify any self-levelling or aftermarket alignment hardware already fitted. Ask what can be measured and corrected after the height is set. Agree any further parts or repair work separately; the standard rear arrangement has no routine camber and toe adjustment.

The current E28 range.

See the controls and hardware in the listed kit.

BC Racing

The current E28 shop entry is I-34 BR RA, listed with pillowball front and rubber rear mounts and nominal spring rates of 6 kg/mm front and 5 kg/mm rear. BR's damping control changes compression and rebound together. Confirm the ordered springs, complete assemblies and fitting instructions for the car. BC's application requires 52mm front struts and welding. Those specifications do not predict ride comfort or approve every E28 variant.

View BC Racing E28 kits

Find your E28 coilovers.

Prices include UK VAT. Choose an application and brand, then open a kit for its current options and availability.

1 listing

Selected application: All E28 applications

Match the drivetrain, body style and axle-load limits on the product page before ordering.

All E28 kit links and part numbers

Before you order.

  1. Identify your car

    Send the full E28 model, engine, build date and original market. Identify M535i or M5 explicitly and describe any previous suspension conversions.

  2. Match the kit

    Have the actual front struts checked against the 52mm I-34 application. Confirm the required welding work and identify any self-levelling or altered rear hardware.

  3. Check what’s included

    Confirm BR RA, the ordered spring specification, complete assemblies and supplied mounts. Ask which existing parts the fitter must retain, replace or repair.

  4. Check your modifications

    Provide wheel widths, offsets, tyre sizes and spacer details. Check arch and suspension clearance through steering and suspension travel at the intended height.

  5. Plan fitting

    Check current availability before booking. Include specialist fitting, height setting, alignment measurement and any agreed correction or follow-up work in the quote.

Questions about BMW E28 coilovers.

Check the details before choosing your kit.

Does the BC Racing I-34 need welding on an E28?

Yes. BC's E28 I-34 application specifies welding. Have the actual front struts assessed and obtain the current kit-specific fitting requirements before ordering. Agree the specialist work and its cost with your fitter. The generic no-welding answer in the shop description conflicts with this application and should not be used to plan the installation.

Can I assume my E28 has the required 52mm struts?

Have the struts on the car checked. BC lists I-34 for the 52mm application, but that row does not establish the diameter or condition of every E28's existing parts. Include any replacement struts or previous conversions in the enquiry.

Is I-34 confirmed for my M535i or M5?

Have the exact model and suspension checked before ordering. The current manufacturer row names the E28 saloon but does not establish every M535i or M5 application. Provide the build details, actual front struts and any self-levelling or modified rear hardware so the complete kit and fitting work can be confirmed.

What if my E28 is an import or has a different registration year?

Send the build date and original market as well as the registration year. BC's kit application says 1981 to 1988; BMW's archive records general-family production from April 1981 to December 1987. Confirm the UK kit against the car's build and actual suspension parts, particularly where its dates or specification are uncertain.

Will coilovers let the fitter adjust rear camber and toe?

The standard E28 rear arrangement has no routine alignment adjustment in BMW's technical description. Have the readings measured and ask what correction is possible with the hardware fitted. Check worn components and mounting areas first. Front camber hardware and a change of dampers do not create rear adjustment.

What do the listed 6/5 kg/mm spring rates tell me?

They are the current shop's nominal front and rear spring figures for I-34 BR RA. Confirm the rates for the kit you order and discuss the car's weight, tyres and use with the fitter. The figures alone do not establish ride comfort, handling balance or suitability for circuit use.

How low should I set my E28?

Agree a height within the exact kit's confirmed usable range, leaving travel and clearance for your roads and normal load. Have wheel clearance checked through steering and suspension movement before the final alignment measurement. An advertised or photographed drop is not a setting for every E28.

What should the fitting quote include?

Include inspection of the struts, mounts and supporting parts, the required welding, and any repairs agreed after inspection. Confirm supplied and retained hardware. Allow for setting the height, checking clearance, measuring alignment and carrying out any separately agreed correction or follow-up work. Confirm current kit availability before booking the car in.

Let’s talk suspension.

Send GSM your E28's full model and build details, the front strut information and any previous suspension changes. Include the wheels and tyres you plan to use so the kit and fitting work can be checked for your car.

Call Coilovers Direct0115 647 9207
or

Your registration isn’t saved to your garage.

Ask about my carFind the listed kits above, or ask us about your setup.